Your Plumbing Crash Course: A Guide to Bathtub Installation
Call TodayAre you currently searching for tips around How to Install a Bathtub?
Installing a bathtub isn't exactly brain surgery, yet it does call for solid plumbing, carpentry, and sometimes, tiling abilities. Replacing an old bath tub with a new one is additionally a reasonably tough project. If the old bathtub is readily accessible, the task can move immediately; if you need to open a wall surface to eliminate the old tub as well as place the new tub, the task is much harder. In either instance, the project is within a house handyman's abilities, although you will need an assistant to leave the old bathtub and also set in the new one. Make certain you have qualified on your own for the job as well as are comfortable trying it. Rather than hiring a contractor to take over a halfway-completed task, it is much better to think about using one prior to you begin. Chances are you might require an expert plumber to make tube links.
This write-up will assist you mount a brand-new bath tub in your restroom if you have actually currently acquired a brand-new tub and also don't require to alter the arrangement of your previous water supply pipelines.
Your devices and also product list should consist of the following:
Planning for the Installation
Firstly, the supporting frame provided with the bathroom ought to be fitted (if called for) according to the manufacturer's guidelines. Next, fit the faucets or mixer to the tub. When fitting the faucet block, it is essential to see to it that if the tap features a plastic washing machine, it is fitted between the bath and also the faucets. On a plastic bath, it is likewise reasonable to fit a sustaining plate under the taps device to prevent pressure on the bathtub.
Fit the versatile faucet connectors to the bottom of both taps making use of 2 nuts and olives (in some cases provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and then pass the outlet with the hole in the bathroom. Use the nut supplied by the manufacturer to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the flexible overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which should be fitted inside the bathroom. Ensure you make use of all of the provided washers.
Link the catch to the bottom of the waste outlet on the tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and also screw on the catch to the outlet. Link all-time low of the overflow tube in a comparable manner.The bath ought to currently prepare to be suited its last position.
Removing Old Taps
If you need to replace old taps with new ones as a part of your setup, after that the first thing you must do is separate the water supply. After doing so, turn on the taps to drain any water remaining in the system. The procedure of getting rid of the existing faucets can be rather troublesome due to the restricted accessibility that is often the instance.
Utilize a basin wrench (crowsfoot spanner) or a faucet tool to reverse the nut that connects the supply pipes to the taps. Have a cloth prepared for the continuing to be water that will originate from the pipelines. When the supply pipes have actually been eliminated, use the very same tool to loosen up the nut that holds the faucets onto the bath/basin. You will require to quit the single faucets from transforming during this process. As soon as the faucets have been eliminated, the holes in the bath/basin will certainly need to be cleaned up of any type of old securing substance.
Before carrying on to fit the brand-new faucets, contrast the pipeline links on the old faucets to the new taps. If the old taps are longer than the new taps, then a shank adapter is required for the new faucets to fit.
Installing the Bathtub
Using both wood boards under its feet, position the bath tub in the needed setting. The wooden boards are practical in uniformly spreading the weight of the bathtub over the location of the boards as opposed to concentrating all the weight onto four tiny points.
The next objective is to ensure that the bathtub is leveled all round. This can be achieved by checking the spirit level and also adjusting the feet on the bath tub till the level reads degree.
To set up faucets, fit the bottom of the outermost versatile faucet port to the ideal supply pipe by making a compression sign up with; then do the same for the other faucet.
Turn on the supply of water and examine all joints and brand-new pipework for leakages as well as tighten them if essential. Fill the tub and additionally examine the overflow electrical outlet as well as the regular outlet for leaks.
Finally, take care of the bathroom paneling as defined in the manufacturer's user's manual. Tiling and securing around the bath tub must wait till the bathtub has been utilized at least once as this will certainly resolve it right into its last setting.
Fitting New Taps
If the tails of the brand-new taps are plastic, then you will need a plastic adapter to prevent damages to the thread. One end of the adapter fits on the plastic tail of the faucet and the various other end supplies a link to the existing supply pipelines.
If you need to fit a monobloc, after that you will certainly need reducing couplers, which links the 10mm pipe of the monobloc to the common 15mm supply pipeline.
Next off, position the tap in the mounting hole in the bath/basin making certain that the washers remain in area in between the faucet and the sink. Safeguard the faucet in position with the maker offered backnut. As soon as the tap is firmly in position, the supply pipelines can be connected to the tails of the taps. The taps can either be connected by using corrugated copper piping or with typical tap ports. The former type ought to be linked to the tap ends first, tightening only by hand. The supply pipes can later be connected to the various other end. Tighten up both ends with a spanner after both ends have actually been linked.
Tiling Around the Bathtub
In the area where the bath fulfills the ceramic tile, it is needed to secure the accompanies a silicone rubber caulking. This is essential as the fitting can relocate enough to crack an inflexible seal, triggering the water to penetrate the wall surface between the bathroom and the tiling, leading to issues with dampness and also possible leakages to the ceiling listed below.
You can select from a selection of coloured sealants to assimilate your components and installations. They are marketed in tubes and cartridges, as well as can sealing spaces approximately a size of 3mm (1/8 inch). If you have a larger gap to fill up, you can load it with spins of soaked newspaper or soft rope. Keep in mind to always fill up the bathtub with water before sealing, to allow for the motion experienced when the bathtub is in use. The sealer can crack rather early if you do not think about this motion before securing.
Conversely, ceramic coving or quadrant floor tiles can be made use of to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and reduce to dimension, are additionally quickly offered on the market. It is a good idea to fit the floor tiles making use of waterproof or water resistant glue as well as grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I'm just very focused on A Step-by-Step Guide to Installing a Bathtub and I hope you enjoyed our article. Please take the opportunity to promote this write-up if you enjoyed reading it. I take joy in reading our article about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.
Plumbing challenges? Professional solutions await.